Surfacing Wire
|
No. |
Headline |
Diameter |
Hardness |
Section Description |
|
1 |
PP-Np-14GST |
1,6 – 3,0 |
18 - 28 |
Surfacing of axes, shafts, rail car wheels, dimension restoration of parts from carbon steels, etc. |
|
2 |
PP-Np-19GST |
1,6 – 3,0 |
26 - 33 |
Surfacing of mounting supports for shafts, axes, rail car wheels, dimension restoration of parts from carbon steels, etc. |
|
3 |
PP-AN105 |
1,6 – 3,0 |
Up to 23 HRC |
Surfacing of railroad frogs, parts of crushing and milling equipment, dimension restoration and defect correction of cast parts |
|
4 |
PP-AN106 |
1,6 – 3,0 |
42 - 48 |
Surfacing of plungers, sealing surfaces for general purpose industrial, gas and oil fittings, rods of hydraulic supports, hydraulic cylinders, etc |
|
5 |
PP-AN120 |
1,6 – 3,6 |
28 - 40 |
Surfacing of crane wheels, rollers of roller tracks, brake pulleys, track vehicle compactors and idlers, mounting supports for shafts, etc |
|
6 |
PP-AN122 |
1,6 – 3,0 |
50 - 56 |
Surfacing of compactors and rollers of track vehicle undercarriages, chambers and augers of rubber mixers, etc |
|
7 |
PP-AN125 |
2,0 – 3,2 |
47 - 58 |
Surfacing of teeth, excavator bucket lips and walls, grizzly bars, knives for graders and bulldozers, grousers, link chains |
|
8 |
PP-AN128 |
1,6 – 3,0 |
42 - 50 |
Surfacing of compactors and rollers of track vehicle undercarriages, chambers and augers of rubber mixers, steel crankshafts, universal joints |
|
9 |
PP-Np-25Kh5FMS |
1,6 – 3,6 |
41 - 51 |
Surfacing of rolls for hot rolling [mostly rolls for finishing mills of pipe-rolling and bar-rolling mills], dies and presses |
|
10 |
PP-AN130 |
1,6 – 3,0 |
43 - 51 |
Surfacing of knives for hot metal cutting, pressing and die tools, rolls for deformed bar rolling, etc. |
|
11 |
PP-AN132 |
1,6 – 3,6 |
47 - 52 |
Surfacing of steel rolls for hot rolling of pipes and bars, knives for hot metal cutting, dies and pressing tools. |
|
12 |
PP-AN133 |
2,0 – 3,4 |
29 - 37 |
Surfacing of sealing surfaces of energy and chemical fittings (plates, saddles, wedges, etc) up to the temperature of 540°С. |
|
13 |
PP-AN135 |
2,6 – 3,2 |
50 - 58 |
Surfacing of teeth and buckets for rocky excavators, rippers and bits for heavy bulldozers in order to operate under permafrost conditions. |
|
14 |
PP-AN138 |
1,8 – 3,0 |
24 - 37 |
Restoration by surfacing of chambers and blades for hydraulic turbines, as well as the other parts subjected to cavitation wear. |
|
15 |
PP-AN147 |
1,6 – 3,6 |
42 - 50 |
Surfacing of rolls for hot rolling [mostly rolls for finishing mills of pipe-rolling and bar-rolling mills], dies and presses |
|
16 |
PP-AN170 |
2,0 – 3,2 |
58 - 67 |
Surfacing of teeth, excavator bucket lips and walls, grizzly bars, knives for graders and bulldozers, grousers, link chains |
|
17 |
PP-AN170М |
2,0 – 3,2 |
58 - 67 |
Surfacing of teeth, excavator bucket lips and walls, grizzly bars, knives for graders and bulldozers, grousers, link chains |
|
18 |
PP-Np-35V9KhZSF |
1,6 – 3,6 |
43 - 54 |
Surfacing of steel rolls for hot rolling of pipes and bars, knives for hot metal cutting, hammer heads, pulling rollers of coiling machines, |
|
19 |
PP-Np-50KhZST |
1,6 – 3,0 |
45 - 55 |
Surfacing of tractor and excavator support rollers, transporter parts, chain drum teeth of multi-bucket excavators, rollers |
|
20 |
PP-AN134G |
1,6 – 3,4 |
42 - 48 |
Surfacing of steel parts subjected to hot gases, wear, corrosion and erosion (piston heads of vessel engines, parts |
|
21 |
PP-AN154М |
1,6 – 3,4 |
42 - 52 |
Surfacing of the parts, which operate under had temperature and deformation conditions during cyclic and thermal impact. |
|
22 |
PP-AN155М |
1,6 – 3,6 |
55 - 62 |
Surfacing of knives for cold and hot cutting, rolls, bandages for manufacturing bearing rings. |
|
23 |
PP-AN156 |
1,6 – 3,6 |
35 - 46 |
Surfacing of metal molds, crystallizer rolls and another parts, which are in a periodic contact with liquid metal (cast iron, aluminum alloys |
|
24 |
PP-AN156М |
1,6 – 3,6 |
36 - 54 |
Surfacing of the parts, which operate under had temperature and deformation conditions during cyclic and thermal impact (metal molds, |
|
25 |
PP-AN158 |
1,6 – 3,6 |
36 - 52 |
Surfacing of plungers for powerful hydraulic presses, CC machine rollers, sealing surfaces of pipe fitting parts, which operate at a temperature |
|
26 |
PP-AN163 |
1,6 – 3,6 |
30 - 40 |
Surfacing of parts, which operate under the conditions of cyclic loads, cavitation wear: marine propeller shafts. |
|
27 |
PP-AN163М |
2,2 – 3,6 |
16 - 25 |
Surfacing of pilger rolls and other parts of pipe-rolling and bar-rolling mill. |
|
28 |
PP-AN167 |
1,6 – 3,2 |
22 - 34 |
Surfacing of impellers, bushings, discs, hydraulic press plungers, crane wheels, parts of automatic coupling devices, hydraulic turbine blade, propeller shafts |
|
29 |
PP-AN168 |
1,6 – 3,0 |
40 - 48 |
Surfacing of parts, which operate under the conditions of abrasive wear (pumping equipment, etc). |
|
30 |
PP-AN185 |
1,6 – 3,6 |
38 - 50 |
Surfacing of CC machine rollers, parts, which are in a periodic contact with liquid metal (steel, cast iron, alloys), hydraulic press plungers, sealing |
|
31 |
PP-AN186 |
1,6 – 3,6 |
30 - 40 |
Surfacing of drilling and pumping equipment details, which operate under the conditions of abrasive wear, corrosion and metal-to-metal friction. |
|
32 |
PP-AN187 |
1,6 – 3,6 |
45 - 54 |
Surfacing of rolls for pipe-rolling and bar-rolling mills, dies and pressing tools. |
|
33 |
PP-Np-12Kh |
1,6 – 3,6 |
30 - 46 |
Surfacing of CC machine rollers, sealing surfaces for general purpose industrial, gas and oil fittings, which operate at a temperature up to 450°С, |
|
34 |
PP-Np-12 |
1,6 – 3,2 |
26 - 35 |
Surfacing of axes, mounting supports for shafts, crane wheels, rail car wheels, dimension restoration of parts from carbon steels |
|
35 |
PP-Np-20Kh7 |
1,6 – 3,6 |
44 - 54 |
Surfacing of rolls for hot rolling, dies, tractor support rollers. |
|
36 |
PP-Np-30Kh20 |
1,6 – 3,2 |
20 - 30 |
Surfacing of hydraulic support rods, hydraulic press plungers, crankshafts. |
|
37 |
PP-Np-40Kh |
1,6 – 3,6 |
44 - 56 |
Surfacing of tractor and excavator support rollers, transporter parts, plowshares, etc. |
|
38 |
PP-Np-40KhZ |
1,6 – 3,6 |
48 - 56 |
Surfacing of parts subjected to impacts and abrasive wear (rolls for hot rolling, dies, support rollers, transporter parts, etc). |
|
39 |
PP-Np-50 |
1,6 – 3,2 |
48 - 58 |
Surfacing of forging and blanking dies for hot rolling, forging machine rolls. |
|
40 |
PP-Np-60 |
1,6 – 3,6 |
48 - 54 |
Surfacing of rolls for pipe-rolling and bar-rolling mills, hot rolling dies. |
|
41 |
PP-Np-100Kh |
1,6 – 3,2 |
40 - 46 |
Surfacing of augers, ripper points of bulldozer attachments, plowshares, cultivator blades, etc. |
|
42 |
PP-Np-150 |
1,6 – 3,2 |
60 - 66 |
Surfacing of hydraulic dredger bodies and impellers, smoke exhauster blades, mixer parts, augers, auger pump liners, operating elements |
|
43 |
PP-Np-180 |
1,6 – 3,2 |
55 - 61 |
Surfacing of teeth and buckets for rocky excavators in order to operate under permafrost conditions, also it is used in mills for crushing solid materials |
|
44 |
PP-Np-250 |
2,0 – 3,2 |
48 - 55 |
Surfacing of parts, which operate under the conditions of abrasive wear with moderate impact loads (coal-pulverizing mill hammers, excavator bucket teeth |
|
45 |
PP-Np-350 |
1,6 – 3,6 |
50 - 58 |
Surfacing of liner plates, concrete mixer blades, and coal-pulverizing equipment parts. |
|
46 |
PP-Np-08 |
1,6 – 3,6 |
≤15 |
Restoration surfacing of axes, shafts, spindles, rollers and also for intermediate layer surfacing. |
|
47 |
PP-Np-20 |
1,6 – 3,6 |
26 - 40 |
Surfacing of track vehicle undercarriage parts, sintering machine elements, rollers of roller tracks, crane wheels, brake pulleys |
|
48 |
PP-Np-25 |
1,6 – 3,6 |
42 - 52 |
Surfacing of track vehicle undercarriage parts, axes, mounting supports for shafts, sintering machine elements, rollers of roller tracks, crane wheels |
|
49 |
PP-Np-15 |
1,6 – 3,6 |
30 - 40 |
Surfacing and repair of defective sections of railroad tracks (rail joint ends, slip places, switch points and other parts of track switch), tram |
|
50 |
PP-Np-50Kh9 |
1,6 – 3,2 |
55 - 60 |
Surfacing of track vehicle wheels and compactors, grader and bulldozer knives, excavator teeth, loading machine parts, transporters and |
|
51 |
PP-Np-180Kh9 |
1,6 – 3,0 |
55 - 62 |
Repair of worn-out parts of mining enterprises and steel works, surfacing of parts for agriculture and construction industry |
|
52 |
PP-Np-30S |
1,6 – 3,2 |
≤20 |
Surfacing of railroad frogs, parts of crushing and milling equipment, dimension restoration and defect correction of cast parts |
|
53 |
PP-Np-30 |
1,6 – 3,6 |
34 - 45 |
Surfacing of track vehicle undercarriage parts, sintering machine elements, rollers of roller tracks, crane wheels, brake pulleys |
|
54 |
PP-Np-10 |
2,0 – 3,4 |
29 - 37 |
Surfacing of sealing surfaces of energy and chemical fittings (plates, saddles, wedges, etc). Temperature up to 540°С |
|
55 |
PP-Np-10Kh |
1,6 – 3,6 |
15 - 38 |
Surfacing sealing surfaces for general purpose industrial fittings for steam and water, which operate at a temperature up to 450ºС. |
|
56 |
PP-Np-15Kh7 |
1,6 – 3,2 |
35 - 45 |
Surfacing of cogging and piercing rolls for hot rolling, as well as pilger mill rolls. |
|
57 |
PP-Np-18 |
1,6 – 3,6 |
23 - 32 |
Surfacing of track vehicle idlers, support rollers, crane wheels, rollers of roller tracks, compactor axes, mounting supports for shafts, restoration |
|
58 |
PP-Np-45 |
1,6 – 3,0 |
50 - 56 |
Surfacing of knives for hot metal cutting, pressing and die tools, rolls for deformed bar rolling, etc. |
|
59 |
PP-AN180MN |
1,6 – 3,0 |
24 - 31 |
Surfacing of axes, crane wheels, mounting supports for shafts, restoration of products and assemblies for railway transport. |
|
60 |
PP-AN180М |
1,6 – 3,0 |
25 - 33 |
Surfacing of axes, crane wheels, mounting supports for shafts, restoration of products and assemblies for railway transport. |
|
61 |
PP-Np-70 |
2,0 – 3,2 |
50 - 56 |
Surfacing of teeth, excavator bucket lips and walls, knives for graders and bulldozers, crusher parts for crushing solid materials, |
|
62 |
PP-Np-80 |
1,8 – 3,2 |
57 - 62 |
Surfacing of coal-pulverizing mill hammers, knives for graders and bulldozers, crusher parts for crushing solid materials. |
|
63 |
PP-Np-100Kh4 |
2,0 – 3,0 |
60 - 62 |
Surfacing of knives for cold and hot cutting of metal, metal cutting and die tools. |
|
64 |
PP-Np-150Kh |
2,0 – 3,2 |
60 - 66 |
Surfacing of inlet augers during brick and concrete production, mixer parts, operating elements of soil processing machines, plowshares |
|
65 |
PP-Np-200 |
1,6 – 3,2 |
58 - 62 |
Surfacing of teeth and buckets for rocky excavators, mills for crushing solid materials, rolling presses, augers, mixers, agricultural equipment parts |
|
66 |
PP-Np-20Kh |
1,6 – 3,6 |
42 - 48 |
Surfacing of hydraulic press plungers, sealing surfaces of pipe fitting parts, which operate at a temperature up to 450 |
|
67 |
PP-Np-30Kh |
1,6 – 3,6 |
48 - 54 |
Surfacing of tractor and excavator support rollers, transporter parts, hydraulic press plungers, crankshaft necks, dies, etc |
|
68 |
PP-Np-180Kh6 |
1,6 – 3,0 |
52 - 58 |
Surfacing of dredging buckets, excavator bucket teeth, grader blades, bulldozer knives, which operate under the most difficult conditions of abrasive wear |
|
69 |
PP-Np-19Kh |
1,6 – 3,2 |
26 - 33 |
Surfacing of mounting supports for shafts, axes, rail car wheels, dimension restoration of parts from carbon steels, etc. |
|
70 |
PP-Np-90 |
1,6 – 3,2 |
55 - 62 |
Surfacing of dies and fast-wearing parts of mining and smelting equipment as well as machinery (dies, punches, axes, rolls, guides |
|
71 |
PP-Np-90Kh18 |
1,6 – 3,2 |
≥45 |
Surfacing of knives for cold cutting, tools for deep drawing, knife cutting edges, parts, which operate under hydraulic and abrasive wear. |
|
72 |
PP-Np-50Kh14 |
1,6 – 3,2 |
50 - 58 |
Surfacing of tools for deep drawing, knife cutting edges, parts, which operate under hydraulic and abrasive wear. |
|
73 |
PP-AN157 |
2,8 – 3,4 |
38 - 52 |
Surfacing of sealing surfaces of energy and chemical fittings, which operate at high environmental parameters up to the temperature of 600°С. |
|
74 |
PP-EL-2S |
2,2 – 3,2 |
≤20 |
Surfacing of parts from austenitic manganese, carbon and low-alloyed steels, mining equipment parts, repair works |
|
75 |
PP-Np-100KhMVF |
2,0 – 3,0 |
60 - 62 |
Surfacing of tools for mechanic treatment, cold shear blades, cutters, knives and guiding devices for wire. |
|
76 |
PP-Np-45V9KhZSF |
1,6 – 3,6 |
44 - 54 |
Surfacing of steel rolls for hot rolling of pipes and bars, knives for hot metal cutting, hammer heads, pulling rollers of coiling machines, |
Surfacing of Parts Is a Modern Method of a Product Correction
Nowadays many things are manufactured from metal. First of all, it is viable, and at the second, we obtain extraordinary strong structures. Metal is durable in itself, but sometimes situations may occur, when it is necessary to correct a product a little bit. Usually a complete replacement is rather expensive, that is why people often refer to another methods. Surfacing of parts is an excellent variant for making a correction. If some of your parts are worn-out or if you have revealed any kind of damage somewhere, you are always able to use the similar method. This is not only practical, this also significantly saves your money. For sure surfacing will suit your product by its composition and mechanical characteristics of metal. These parts are capable not only to restore the ideal condition of any metallic material, but also will add a novelty to it.
Surfacing of Metal - Profitable And Prompt
There are several requirements to this process. Metal penetration should be minimum in order not to damage anything. There should be no deformations at the place, where a surfacing of metal is required. Everything should comply with certain standards, which enable the further treatment of metal. The surfacing technology is rather peculiar. For this purpose you have to make several actions, including deposition by filar beads, as well as their correct deployment. For sure, it may seem a difficult process at first sight, but the experts in this area will definitely help you to do everything in a quick and prompt way. You can order a surfacing of parts at our Web-site. We have everything, which is required for this purpose. Please contact us and we will definitely restore a perfect outlook to any metallic products in a prompt and qualitative way without extra expenses.